Linux, Scanner - Ausgaben von scanimage -A benötigt

[TS]

Hello,

nützt dir die Ausgabe von scanimage -A von meinem Snapscan? Das ist ein uralter Agfa-Scanner; leider zur Zeit der einzige, der bei mir noch läuft.

tschmieder@traveller:~$ scanimage -A
p11-kit: invalid config filename, will be ignored in the future: /etc/pkcs11/modules/gnome-keyring-module
[snapscan] Scanner warming up - waiting 15 seconds.

All options specific to device `snapscan:libusb:005:003':
  Scan Mode:
    --resolution auto||50|75|100|150|200|300|450|600dpi [300]
        Sets the resolution of the scanned image.
    --preview[=(auto|yes|no)] [no]
        Request a preview-quality scan.
    --mode auto|Color|Halftone|Gray|Lineart [Color]
        Selects the scan mode (e.g., lineart, monochrome, or color).
    --preview-mode auto|Auto|Color|Halftone|Gray|Lineart [Auto]
        Select the mode for previews. Greyscale previews usually give the best
        combination of speed and detail.
    --high-quality[=(auto|yes|no)] [no]
        Highest quality but lower speed
    --source auto|Flatbed [inactive]
        Selects the scan source (such as a document-feeder).
  Geometry:
    -l auto|0..216mm [0]
        Top-left x position of scan area.
    -t auto|0..297mm [0]
        Top-left y position of scan area.
    -x auto|0..216mm [216]
        Width of scan-area.
    -y auto|0..297mm [297]
        Height of scan-area.
    --predef-window None|6x4 (inch)|8x10 (inch)|8.5x11 (inch) [None]
        Provides standard scanning areas for photographs, printed pages and
        the like.
  Enhancement:
    --depth 8bit [inactive]
        Number of bits per sample, typical values are 1 for "line-art" and 8
        for multibit scans.
    --quality-cal[=(yes|no)] [yes]
        Do a quality white-calibration
    --halftoning[=(yes|no)] [inactive]
        Selects whether the acquired image should be halftoned (dithered).
    --halftone-pattern DispersedDot8x8|DispersedDot16x16 [inactive]
        Defines the halftoning (dithering) pattern for scanning halftoned
        images.
    --custom-gamma[=(yes|no)] [no]
        Determines whether a builtin or a custom gamma-table should be used.
    --analog-gamma-bind[=(yes|no)] [no]
        In RGB-mode use same values for each color
    --analog-gamma 0..4 [inactive]
        Analog gamma-correction
    --analog-gamma-r 0..4 [1.79999]
        Analog gamma-correction for red
    --analog-gamma-g 0..4 [1.79999]
        Analog gamma-correction for green
    --analog-gamma-b 0..4 [1.79999]
        Analog gamma-correction for blue
    --gamma-table 0..65535,... (in steps of 1) [inactive]
        Gamma-correction table.  In color mode this option equally affects the
        red, green, and blue channels simultaneously (i.e., it is an intensity
        gamma table).
    --red-gamma-table 0..65535,... (in steps of 1) [inactive]
        Gamma-correction table for the red band.
    --green-gamma-table 0..65535,... (in steps of 1) [inactive]
        Gamma-correction table for the green band.
    --blue-gamma-table 0..65535,... (in steps of 1) [inactive]
        Gamma-correction table for the blue band.
    --negative[=(auto|yes|no)] [inactive]
        Swap black and white
    --threshold 0..100% (in steps of 1) [inactive]
        Select minimum-brightness to get a white point
    --brightness -400..400% (in steps of 1) [0]
        Controls the brightness of the acquired image.
    --contrast -100..400% (in steps of 1) [0]
        Controls the contrast of the acquired image.
  Advanced:
    --rgb-lpr auto|1..50 (in steps of 1) [4]
        Number of scan lines to request in a SCSI read. Changing this
        parameter allows you to tune the speed at which data is read from the
        scanner during scans. If this is set too low, the scanner will have to
        stop periodically in the middle of a scan; if it's set too high,
        X-based frontends may stop responding to X events and your system could
        bog down.
    --gs-lpr auto|1..50 (in steps of 1) [inactive]
        Number of scan lines to request in a SCSI read. Changing this
        parameter allows you to tune the speed at which data is read from the
        scanner during scans. If this is set too low, the scanner will have to
        stop periodically in the middle of a scan; if it's set too high,
        X-based frontends may stop responding to X events and your system could
        bog down.

Der läuft auch nur noch mit Linux. Die Scanprogramme dafür unter Windows haben alle am selben Tag die Leistung verweigert :-(

Ich muss mir im November spätestens einen neuen kaufen. Was sollte ich beachten? Welcher ist empfehlenswert. Es mus nicht der billigste sein, aber auch nicht aus Gold.

Liebe Grüße
Tom S.