Wie COM-Port in Linux System herausfinden?

[Karl Heinz]

Das habe ich in minicom eingetragen. Box dann neu gestartet. Ich bin drin in der Bootsequenz. Danke, du hast mir mein TV Wochenende auf Sky gerettet :-).

Mist, ich habe es doch noch nicht ganz gelöst. Betätige ich während des Bootvorgangs STRG+C, so komme ich leider nicht in die Shell um Eingaben zu machen, STRG+C bringt keine Reaktion. Eine Ahnung wie ich in die Eingabe der Shell kommmen kann?

Hier mal die Ausgabe der Box:

Willkommen zu minicom 2.7

Optionen: I18n Übersetzt am Jan 1 2014, 17:13:19. Port /dev/ttyUSB0, 12:03:03

Drücken Sie CTRL-A Z für Hilfe zu speziellen Tasten

Dreambox DM520

M0CZS L2=1 LLMB=1 BrCfg=E30FB7C6 #@

BCM973625A0 CFE v15.3, Endian Mode: Little Build Date: Fri Aug 19 11:48:16 2016 (Jann@Cynric) Copyright (C) Broadcom Corporation.

Non-CI box detected card if inited Enabling NAND flash at CS2: A5U4GA31ATS(DEVICE ID=0xC8DC9095), ECC Level=4, Spare Area Size=16 MACRONIX SPI flash detected: Size = 16MB, Sector Size 4096, Page Size 256

CPU speed: 751MHz DDR Frequency: 1061 MHz DDR Mode: DDR3 Total memory(MEMC 0): 512MB MEMC 0 DDR Width: 16 Boot Device: SPI Total flash: 16MB RTS VERSION: rts_hevc10_1067 ETH0_PHY: INT ETH0_MDIO_MODE: 1 ETH0_SPEED: 100 ETH0_PHYADDR: 1

DM init finalization yxml: processing file of 131072 bytes... succeeded! no file loaded, create xml restoring default xml loaded network params of: DHCP, 192.168.0.219, 255.255.255.0, 192.168.0.1 [1] type 3, dev nandflash0.kernel, loader elf, filesys raw, file , options [2] type 3, dev flash0.kernel, loader elf, filesys raw, file , options [3] type 1, dev eth0, loader elf, filesys tftp, file , options bmem=192M@64M console=ttyS0,1000000 root=/dev/nfs ip=dhcp added 3 sources to autoboot list init fp Initializing USB.

CFE initialized. found card in unknown state ca valid!

***** DREAMBOX SSBL *****

Not interrupted yet, trying autoboot or rescue loader, hit any key in the next 500ms to cancel Proceeding with autoboot.. You can try aborting with Ctrl+C

*** Autoboot: Trying device 'nandflash0.kernel' file (raw,elf)

Ethernet link is up: 100 Mbps Full-Duplex Loader:elf Filesys:raw Dev:nandflash0.kernel File: Options: Loading: 0x80001000/7588032 0x8073d8c0/235952 Entry address is 0x805cd1d0 Closing network eth0 Starting program at 0x805cd1d0

�[ 0.234000] console [ttyS0] enabled, bootconsole disabled [ 0.234000] console [ttyS0] enabled, bootconsole disabled [ 0.239000] loop: module loaded [ 0.240000] brcmstb_nand: NAND controller driver is loaded [ 0.240000] tun: Universal TUN/TAP device driver, 1.6 [ 0.241000] tun: (C) 1999-2004 Max Krasnyansky [e-mail] [ 0.363000] bcmgenet: configuring instance #0 for internal PHY [ 0.383000] bcmgenet bcmgenet.0: (unregistered net_device): link down [ 0.384000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.385000] ehci-brcm ehci-brcm.0: Broadcom STB EHCI [ 0.385000] ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1 [ 0.417000] ehci-brcm ehci-brcm.0: irq 66, io mem 0x10480300 [ 0.423000] ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00 [ 0.424000] hub 1-0:1.0: USB hub found [ 0.424000] hub 1-0:1.0: 2 ports detected [ 0.425000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.426000] ohci-brcm ohci-brcm.0: Broadcom STB OHCI [ 0.426000] ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 2 [ 0.427000] ohci-brcm ohci-brcm.0: irq 67, io mem 0x10480400 [ 0.493000] hub 2-0:1.0: USB hub found [ 0.494000] hub 2-0:1.0: 2 ports detected [ 0.494000] Initializing USB Mass Storage driver... [ 0.495000] usbcore: registered new interface driver usb-storage [ 0.496000] USB Mass Storage support registered. [ 0.496000] i2c /dev entries driver [ 0.497000] lirc_dev: IR Remote Control driver registered, major 253 [ 0.497000] usbcore: registered new interface driver btusb [ 0.499000] TCP: cubic registered [ 0.499000] NET: Registered protocol family 10 [ 0.501000] NET: Registered protocol family 17 [ 0.501000] Bluetooth: RFCOMM TTY layer initialized [ 0.502000] Bluetooth: RFCOMM socket layer initialized [ 0.503000] Bluetooth: RFCOMM ver 1.11 [ 0.503000] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 0.504000] Bluetooth: BNEP filters: protocol multicast [ 0.504000] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 0.505000] L2TP core driver, V2.0 [ 0.506000] Registering the dns_resolver key type [ 0.506000] PM: CP0 COUNT/COMPARE frequency does not depend on divisor [ 0.508000] EBI CS2: setting up NAND flash (primary) [ 0.509000] NAND device: Manufacturer ID: 0xc8, Chip ID: 0xdc (Unknown NAND 512MiB 3,3V 8-bit) [ 0.510000] brcmnand brcmnand.0: 512MiB total, 128KiB blocks, 2KiB pages, 16B OOB, 8-bit, BCH-4 [ 0.510000] [ 0.512000] Bad block table found at page 262080, version 0x01 [ 0.513000] Bad block table found at page 262016, version 0x01 [ 0.514000] nand_read_bbt: bad block at 0x00000ba80000 [ 0.516000] Creating 3 MTD partitions on "brcmnand.0": [ 0.516000] 0x000000000000-0x00001f500000 : "rootfs" [ 0.518000] 0x000000000000-0x000020000000 : "entire_device" [ 0.520000] 0x00001f500000-0x00001fa00000 : "kernel" [ 0.522000] EBI CS0: setting up SPI flash [ 0.522000] spi_brcmstb spi_brcmstb.0: 1-lane output, 3-byte address [ 0.523000] spi_brcmstb spi_brcmstb.0: master is unqueued, this is deprecated [ 0.524000] m25p80 spi0.0: found mx25l12805d, expected w25q128bv [ 0.525000] m25p80 spi0.0: mx25l12805d (16384 Kbytes) [ 0.527000] UBI: attaching mtd0 to ubi0 [ 0.527000] UBI: physical eraseblock size: 131072 bytes (128 KiB) [ 0.528000] UBI: logical eraseblock size: 126976 bytes [ 0.529000] UBI: smallest flash I/O unit: 2048 [ 0.529000] UBI: VID header offset: 2048 (aligned 2048) [ 0.530000] UBI: data offset: 4096 [ 3.677000] UBI: max. sequence number: 13179 [ 3.693000] UBI: attached mtd0 to ubi0 [ 3.693000] UBI: MTD device name: "rootfs" [ 3.694000] UBI: MTD device size: 501 MiB [ 3.695000] UBI: number of good PEBs: 4007 [ 3.695000] UBI: number of bad PEBs: 1 [ 3.696000] UBI: number of corrupted PEBs: 0 [ 3.696000] UBI: max. allowed volumes: 128 [ 3.697000] UBI: wear-leveling threshold: 4096 [ 3.697000] UBI: number of internal volumes: 1 [ 3.698000] UBI: number of user volumes: 1 [ 3.698000] UBI: available PEBs: 0 [ 3.699000] UBI: total number of reserved PEBs: 4007 [ 3.699000] UBI: number of PEBs reserved for bad PEB handling: 40 [ 3.700000] UBI: max/mean erase counter: 8/4 [ 3.701000] UBI: image sequence number: 1245690932 [ 3.701000] UBI: background thread "ubi_bgt0d" started, PID 53 [ 3.703000] ALSA device list: [ 3.704000] No soundcards found.

[ 3.755000] UBIFS: recovery needed [ 3.815000] UBIFS: recovery completed [ 3.815000] UBIFS: mounted UBI device 0, volume 0, name "dreambox-rootfs" [ 3.816000] UBIFS: file system size: 501301248 bytes (489552 KiB, 478 MiB, 3948 LEBs) [ 3.817000] UBIFS: journal size: 25141248 bytes (24552 KiB, 23 MiB, 198 LEBs) [ 3.818000] UBIFS: media format: w4/r0 (latest is w4/r0) [ 3.819000] UBIFS: default compressor: lzo [ 3.819000] UBIFS: reserved for root: 4952683 bytes (4836 KiB) [ 3.821000] VFS: Mounted root (ubifs filesystem) on device 0:12. [ 3.821000] devtmpfs: error mounting -2 [ 3.822000] Kernel panic - not syncing: No init found. Try passing init= option to kernel. See Linux Documentation/init.txt for guidance. [ 3.823000] Rebooting in 180 seconds..